Crown Barrel Shroud – Threaded
$59.99
468 Customers Have Purchased This Item!
This Crown-style Barrel Shroud from Tacticool22 gives your gun barrel the cool, aggressive look you’ve always wanted.
Product Description
This crown-style Barrel Shroud fits AR-10, AR-15, S&W M&P15-22, and other rifles with threaded barrels, and is offered in multiple thread pattern configurations.
Crown Barrel Shroud Features
- Black, hard-coat anodized finish to MIL-SPEC Type III.
- Quickly and easily threads onto your barrel.
- Does not lengthen the barrel.
- Does not quiet the firearm.
- Made in the USA.
Barrel Shroud Measurements
We offer multiple measurements and thread options to ensure a proper fit for your firearm. If you’re not sure which options to pick, please contact us.
- Diameter:
- Outside 1 1/4 inch
- Inside 1 inch
- Length: 6″
- Threads:
- 1/2″-28 (fits threaded .22, .223, .556, S&W M&P15-22, etc)
- 1/2″-36
- 5/8″-24 (fits threaded .300, .308, etc)
- 9/16″-24
- 37/64″-28
- M14x1 RH
- M14x1 LH
- Custom thread. Please provide your rifle’s thread diameter and TPI in the order notes during checkout.
For example, 1/2-28 = .500 inch diameter, 28 threads per inch.
Additional Information
| Weight | 0.3 oz |
|---|---|
| Caliber | .22, .223/5.56mm, .25/6.5mm, .30/7.62mm, .308/7.62mm |
| Color | Black |
| Finish | Hardcoat Anodized to MIL-SPEC Type III |
| Firearm Compatibility | AR-15, Smith & Wesson M&P15-22 |
| Material | Aluminum |
| Thread Pattern | 37/64-28, 1/2-28, 1/2-36, 5/8-24, 9/16-24, M14x1 LH, M14x1 RH, Custom Thread |
1 review for Crown Barrel Shroud – Threaded
Only logged in customers who have purchased this product may leave a review.
Measurement Requirements are required ONLY for custom thread and/or Custom Length
Please include the following information in the Order Notes during checkout or email us at [email protected]/* */ immediately after your purchase.
- Custom Thread – Provide the following thread information:
- Thread diameter
- Thread pitch
- Model of firearm
You must measure with quality metal calipers or micrometer to ensure a proper fit.
ATTENTION: If you do not provide measurements during checkout, we will send you an email asking for the missing information.
Related products
Barrel Shrouds
Barrel Shrouds
Barrel Shrouds
Note: It is your responsibility to review and follow all United States of America federal, state, and/or local laws and regulations related to the use, possession, purchase and/or ownership of restricted items. And of course, be safe and have fun.
nikondutch –
Had my dear wife pick this up for Christmas, once again I proved that patience is not my specialty. Removing the “flash suppressor” was not difficult, used 1 each vise, 4″ piece of inner tube, and two pieces of hardwood. Squeeze factor major to keep the barrel from turning. Used an open end wrench and it was a done deal. I did replace the crush washer, seemed like the right thing to do. The shroud required the removal of the end cap from the fore grip – easy (Jody said use chopsticks) he was correct. Slipped on the shroud and torqued it down. it was about the same weight as the suppressor but it has a coolness factor that is way higher (I’m in my late 60’s and still enjoy coolness). Accuracy was not changed still shooting sub 1″ groups with scope and little over 1″ with the red dot. Go for it it’s a fun upgrade.